Developers and makers are invited to discover the flexibility of a low-power programmable gate array. The Intel® Cyclone® 10 LP Evaluation Kit provides an easy-to-use platform for evaluating Intel Cyclone 10 LP FPGA technology and Intel Enpirion® regulators. With this evaluation board, you can: • Develop designs for Intel Cyclone 10 LP FPGA devices • Bridge to functions or devices via Arduino UNO R3 shields, PMOD, GPIO or Ethernet connectors • Measure key Intel Cyclone 10 LP FPGA power supplies • Reuse the kit's PCB schematic & design files to start your design quickly Whether you are an FPGA developer, software developer, maker, seasoned IoT developer, coding newbie, or just curious about FPGAs, we hope your experience with the Intel Cyclone 10 LP FPGA kit is both informative and fun.

• ZC706 Restoring Flash Contents October 2014 XTP247. The Twilight Breaking Dawn Part 1 In Hindi Counter more. • NOTICE OF DISCLAIMER: The information disclosed to you hereunder (the “Information”) is provided “AS-IS” with no warranty of any kind, express or implied.

Xilinx does not assume any liability arising from your use of the Information. You are responsible for obtaining any rights you may require for your use of this Information. • Overview Xilinx ZC706 Board Software Requirements ZC706 Setup Restoring ZC706 QSPI Flash References Note: This presentation applies to the ZC706. • ZC706 Board. • Vivado Software Requirements Xilinx Vivado Design Suite 2014.3, Design Edition + SDK – Combined installer Note: Presentation applies to the ZC706.

• ZC706 Setup Set the JTAG Select Switch, SW4, to 01 – If using a Platform Cable USB (II) JTAG Cable, set SW4 to 10 Note: Presentation applies to the ZC706. • ZC706 Setup Connect a USB Type-A to Micro-B cable to the USB JTAG (Digilent) connector on the ZC706 board – Connect this cable to your PC – Power on the ZC706 board. • ZC706 Setup Connect a USB Type-A to Mini-B cable to the USB UART connector on the ZC706 board – Connect this cable to your PC – Power on the ZC706 board for UART Drivers Installation. • ZC706 Setup Install USB UART Drivers – Refer to UG1033 for details on installing the USB to UART Drivers Note: Presentation applies to the ZC706.

• ZC706 Setup Reboot your PC if necessary Right-click on My Computer and select Properties – Select the Hardware tab – Click on Device Manager Note: Presentation applies to the ZC706. • ZC706 Setup Expand the Ports Hardware – Right-click on Silicon Labs CP210x USB to UART Bridge and select Properties Note: Presentation applies to the ZC706. • ZC706 Setup Under Port Settings tab – Click Advanced – Set the COM Port to an open Com Port setting from COM1 to COM4 Note: Presentation applies to the ZC706. • ZC706 Setup Refer to UG1036 regarding Tera Term installation Board Power must be on before starting Tera Term Start the Terminal Program – Select your USB Com Port – Set the baud to 115200 Note: Presentation applies to the ZC706. • Restoring ZC706 QSPI Flash. • Restoring ZC706 QSPI Flash Set the SW11 DIP switches to: 00000 Note: Presentation applies to the ZC706.

• Restoring ZC706 QSPI Flash Unzip the ZC706 Restoring Flash Design Files (2014.3 C) ZIP file to your C: drive – Available through Note: Presentation applies to the ZC706. • Restoring ZC706 QSPI Flash Open a Windows prompt Cycle ZC706 Power if any programs have been run Program the QSPI Flash cd C: zc706_restore_flash program_dual_qspi.bat Note: Takes about 3 minutes.

• Restoring ZC706 QSPI Flash Set the SW11 DIP switches to boot from QSPI: 00010 Note: Presentation applies to the ZC706. • Restoring ZC706 QSPI Flash View initial BIST screen Note: Presentation applies to the ZC706. • References. • References 7 Series Configuration – 7 Series FPGAs Configuration User Guide – UG470 • ug470_7Series_Config.pdf.

• Documentation. • Documentation Zynq-7000 – Zynq-7000 All Programmable SoC • ZC706 Documentation – Zynq-7000 AP SoC ZC706 Evaluation Kit • – ZC706 Getting Started Guide – UG961 • ug961-zc706-GSG.pdf – ZC706 User Guide – UG954 • ug954-zc706-eval-board-xc7z045-ap-soc. Nvidia Geforce Fx 5200 Driver Download Windows 7 64 Bit. pdf.

Installing impact and the Digilent configuration cable drivers are not always a smooth task. The USB-JTAG cable is not supported directly with the driver provided by Xilinx in the Lab Tools, therefore it is necesarry to install external drivers. In the Xilinx forums it is possible to find a great number of questions. 250-003 is a JTAG-USB cable which allows a PC to connect to a JTAG scan chain or to access the SPI interface on a board equipped with the appropriate 6 pin header. In this way, the user can program devices on programmable logic boards using the Digilent Adept Suite. Similarly, the user can also program AVR.